Lignin-based additives for Biomass Pelleting
Natural performance. Higher-quality pellets.
Biomass pellet producers are under increasing pressure to deliver more: higher throughput, greater pellet durability, lower energy costs and compliance with stricter sustainability certifications. Bio-based chemistry can meet these evolving demands without compromise.
Borregaard's lignin-based pelleting aids enable this shift by improving binding, lubrication and energy content, while supporting sustainable, wood-based formulations that fit naturally into a certified fuel-pellet supply chain.
STRONG BINDING
Creates stronger internal cohesion between wood particles, reducing fines and increasing pellet durability.
EFFECTIVE LUBRICATION
Eases material flow through the pellet die, lowering press amperage and enabling higher production rates.
REDUCED SELF-HEATING
Positively impacts the self-heating tendency of stored pellets, supporting safer handling and storage.
Proven performance. By the numbers.
A demonstration at a commercial wood pelleting plant in the United States shows that LignoBond 870L increased production rate, reduced power consumption and improved pellet durability:
Monitoring began with a feeder-screw speed of 38 Hz, power consumption of 99.9 kWh/ton and pellet durability of 96.4. Once LignoBond 870L was applied at a rate of 0.73% liquid on fibre, amperage dropped immediately, power consumption fell to 83.3 kWh/ton and durability rose to 97.2. When production was subsequently increased by 21%, LignoBond 870L dosage was reduced to 0.60%, power consumption settled at 80.8 kWh/tonne and durability remained high at 96.9. When LignoBond 870L was shut off, amperage and power consumption rose again and durability fell to 96.5 – confirming the additive's direct impact on process performance.
Independent dosage trials, tested with the Ligno-Tester, show a similar pattern: pellet durability (PDI) rose from 94.7% with no LignoBond, to 96.4% at a 0.5% dosage, and to 96.7% at a 1.0% dosage.
Formulation considerations
LignoBond 870L contains 3.5% sulphur in the liquid product. At typical dosing rates of 0.5–1% liquid-based-on-wet-pellet (lbwp), this introduces approximately 0.0175–0.035% sulphur into the finished pellet, within the ≤0.05% total sulphur limit set by ENplus/ISO 17225-2 (I2, I3 quality pellets). Dosage should therefore be selected in consultation with Borregaard's technical team to balance binding and lubrication performance against total sulphur specifications and treatment cost.
Why this matters across the industry
The gains shown above are not incidental. They respond to pressures every pellet producer is facing:
- Rising global demand for certified, low-carbon biomass fuel
- Pressure to reduce fines, dust and explosion risk on the production floor
- High electricity costs and significant equipment wear from pelleting operations
- The need for pellets with high energy content and low moisture
- Sustainability and chain-of-custody certification requirements across the value chain
Few additive solutions deliver on all of these fronts at once. LignoBond 870L's combination of binding, lubrication and certified sustainability is exactly what makes the difference.
Derived from sustainably sourced wood, LignoBond 870L brings this functionality to biomass pelleting and, as a wood-based raw material rather than a synthetic additive, it fits directly into a certified wood-pellet supply chain.
The science behind lignin in biomass pelleting
Lignin's key contribution lies in its ability to act as a natural binder and lubricant during the pelleting process. Under the heat and pressure of the pellet mill, it improves cohesion between wood particles while easing material flow through the die. This combination produces stronger, more durable pellets with reduced fines and lower press wear.
This enables producers to achieve more, with less complexity and improved sustainability:
Enhanced Pellet Performance
- Improved physical pellet quality and reduction of fines and dust
- Increased pellet durability (PDI), demonstrated at a commercial wood pelleting plant
- Positive impact on the net calorific value (NCV) of finished pellets
Synergy with Pelleting Operations
- Lubricates the pellet mill, reducing press amperage and energy consumption
- Enables higher throughput without added capital equipment
- Compensates for variations in raw material quality for production
Sustainability Without Compromise
- Bio-based material produced from sustainable and controlled wood
- Certified chain of custody as a wood pellet raw material; LignoBond 870L is PEFC certified
- A wood raw material, not a synthetic additive, fitting naturally into certified pellet supply chains
Improved Safety and Environmental Profile
- Reduced self-heating tendencies, reducing combustion risk in storage
- Lower dust levels and reduced dry-dust explosion potential
- Measurable reductions in power consumption per tonne of pellets produced
Sustainability & certifications
- Documented low climate footprint — Borregaard products provide better environmental performance than alternatives in almost all environmental categories.
- Aligned with the UN 2030 Agenda — Borregaard has prioritised six of the seventeen Sustainable Development Goals, including Zero Hunger (SDG 2), Decent work and economic growth (SDG 8), Industry, innovation and infrastructure (SDG 9), Responsible consumption and production (SDG 12), Climate action (SDG 13) and Life on land (SDG 15).
- Certified in accordance with several international standards, including PEFC chain-of-custody certification for LignoBond 870L.
Let's discuss your biomass pelleting operation
Derived from sustainably sourced wood, LignoBond 870L combines bio-based origin with functional performance – helping pellet producers meet quality, efficiency and sustainability targets without compromise.
With deep knowledge of both pelleting and wood chemistry, Borregaard helps tailor lignin-based pelleting aids to specific feedstocks and operating conditions, delivering reliable, high-performance results.
Frequently Asked Questions
-
What is LignoBond 870L?
LignoBond 870L is a lignin-based pelleting aid from Borregaard, supplied by LignoTech Florida. It is a liquid raw material produced from a natural, renewable wood source, and is used as a binding and lubricating aid in the manufacture of wood and biomass fuel pellets.
-
Is LignoBond 870L an additive, or a raw material?
LignoBond 870L is classified as a wood pellet raw material, not a synthetic additive. It carries a certified chain of custody, which allows pellet producers to include it in certified, sustainably sourced pellet formulations.
-
How does LignoBond 870L improve pellet quality?
As a lignin-based product, it is multifunctional in the pellet mill: it binds wood particles together, lubricates material flow through the die, contributes usable energy content, and reduces the self-heating tendency of finished pellets. In field trials, this translated into higher pellet durability (PDI), fewer fines and dust, and lower press amperage.
-
What results has LignoBond 870L achieved in real production?
In a demonstration at a commercial wood pelleting plant in the United States, applying LignoBond 870L increased production rate by 21%, reduced power consumption from 101 to 81 kWh/ton, and improved pellet durability (PDI) from 96.5 to 96.9. Separate dosage trials using the Ligno-Tester showed pellet durability rising from 94.7% with no LignoBond to 96.7% at a 1.0% dosage.
-
What dosage rate is typically used?
Dosage is generally in the range of 0.5–1.0% liquid based on wet pellet (lbwp), depending on feedstock, target pellet durability and production rate. Borregaard works with each producer to determine the optimal dosage for their specific raw material mix and operating conditions.
-
Does LignoBond 870L affect the sulphur content of finished pellets?
LignoBond 870L contains 3.5% sulphur in the liquid product. At typical dosing rates of 0.5–1% lbwp, this introduces approximately 0.0175–0.035% sulphur into the finished pellet, which stays within the ≤0.05% total sulphur limit required by ENplus/ISO 17225-2 for I2 and I3 quality pellets used in applications such as coal co-firing.
-
Does LignoBond 870L reduce the energy value of the pellets?
No. Application of LignoBond 870L has no negative impact on the net caloric value (NCV) of finished pellets. In fact, LignoBond itself has a higher calorific value than wood (20.3 GJ/MT), so it can contribute positively to the pellet's overall energy content.
-
How does LignoBond 870L improve safety in pellet production and storage?
By binding fines and reducing dust generation, LignoBond 870L lowers the risk of dry-dust explosions during processing. It also has a positive impact on the self-heating tendency of stored pellets, which reduces the risk of spontaneous combustion during storage and transport.
-
Is LignoBond 870L sustainable and certified?
Yes. LignoBond 870L is produced from a natural and renewable wood source, is PEFC certified, and carries a certified chain of custody as a wood pellet raw material. Borregaard's products also have documented low climate footprints and support several of the UN Sustainable Development Goals, including Industry, Innovation & Infrastructure (SDG 9), Climate Action (SDG 13) and Life on Land (SDG 15).
-
How is LignoBond 870L delivered and handled on site?
LignoBond 870L is supplied as a liquid, typically delivered in bulk via Flexibag-lined containers, drums or totes (IBCs), and unloaded using standard liquid transfer pumps and camlock fittings. Borregaard provides handling guidance to help producers integrate it safely into existing liquid-dosing systems at the pellet mill.
-
Why is Borregaard well suited to supply pelleting aids?
Borregaard combines strong technical competence in both pelleting operations and wood chemistry. As the world's leading supplier of lignin-based products, with a global network of production plants, Borregaard can offer pellet producers both a reliable, sustainably sourced raw material and hands-on technical support to optimise its use.
.png?width=517&height=128&name=Group%20(2).png)